- You cannot place a new order from your country (United States).
search
Adjust-A-Wing Lamp Holder
The Adjust-A-Wing Lamp Holder is the genuine E40 socket assembly from Australian manufacturer Adjust-A-Wings, designed as a direct replacement or additional light point for all sizes and models of Adjust-A-Wings reflectors. The height-adjustable ceramic E40 fitting allows precise positioning of the lamp within the reflector for optimal light output, and is rated for HPS and MH lamps up to 1000W. Essential for growers adding a second lamp to an Avenger Large setup, or replacing a worn original socket. Supplied without cable. Compatible with Enforcer, Avenger and Defender SE models. Fast shipping to Belgium from plantandflower.be.
Adjust-A-Wing Lamp Holder E40 — Genuine Replacement Socket for All Adjust-A-Wings Reflectors
When a component in your lighting setup fails, substituting with a non-original part introduces compatibility risk — particularly at the lamp-reflector interface where thermal tolerance and electrical geometry directly affect both safety and light output. The Adjust-A-Wing Lamp Holder is the factory-original E40 ceramic socket assembly, designed to fit all single-ended models across the entire Adjust-A-Wings reflector range with zero compromise.
Universal fit across the Adjust-A-Wings lineup
The E40 lamp holder slides into the central mounting channel of any SE (Single Ended) Adjust-A-Wings reflector and locks with two thumb screws — no tools required:
- Avenger Medium and Large: direct replacement for the factory-fitted socket, or a second holder for dual-lamp operation on the Large.
- Enforcer Small, Medium and Large: full compatibility for replacement use.
- Defender SE: compatible with the single-ended variant only.
The ceramic E40 socket withstands the sustained high temperatures generated by discharge lamps up to 1000W — a critical specification that plastic-bodied aftermarket alternatives often fail to meet over time. The height-adjustment mechanism ensures the lamp sits at the precise focal point of the parabolic wing geometry, maximising reflector efficiency. Combine with high-output lamps like the Lumatek HPS 400W for a reliable, performance-optimised setup.
Three scenarios where you need this holder
The Adjust-A-Wing Lamp Holder addresses three practical situations. First, replacement after wear or damage: ceramic sockets are highly durable, but any sign of heat discolouration, cracking or a loose lamp connection warrants immediate replacement for electrical safety. Second, dual-lamp expansion: the Avenger Large and Enforcer Large are designed to accept a second holder at the opposite end, enabling two 400W or 600W lamps under one reflector for maximum canopy coverage. Third, DIY or kit assembly: some reflectors are supplied without a socket, or growers sourcing components separately need the correct original part for a first-time build.
Installation notes
The lamp holder is supplied without IEC cable. A separate IEC cable is required to connect the holder to your ballast — most modern electronic ballasts ship with a female IEC connector that pairs directly with a standard IEC lamp lead. The holder attaches to the Avenger Medium or any compatible reflector via the included mounting bracket and two thumb screws in under a minute.
The genuine Adjust-A-Wing Lamp Holder is stocked and available with fast delivery for Belgian growers at plantandflower.be. Always use original components to maintain the design integrity and safety of your Adjust-A-Wings lighting system.
Which Adjust-A-Wings reflector models is this lamp holder compatible with?
The E40 lamp holder is compatible with all Adjust-A-Wings reflectors that use single-ended (SE) lamps: the Avenger Medium and Large, the Enforcer Small, Medium and Large, and the Defender SE. It is not suitable for the Defender DE (Double Ended) variant, which uses double-ended lamps with a different socket type. Always confirm whether your reflector is SE or DE before ordering.
Does the Adjust-A-Wing Lamp Holder come with a cable?
No, this version is supplied without an IEC cable. You will need a separate IEC lamp lead to connect the holder to your ballast. Some retailers sell a version with a 4-metre IEC cable included — check the product listing carefully. The mounting bracket and thumb screws for attaching the holder to the reflector are included.
Can I add a second lamp holder to my Adjust-A-Wing Avenger Large?
Yes. The Avenger Large is specifically designed to accept a second lamp holder at the far end of the reflector, allowing two E40 HPS or MH lamps to operate under one reflector. Each holder requires its own ballast. This dual-lamp configuration is not supported on the Medium model, which is sized for a single lamp only.
What is the maximum wattage for the Adjust-A-Wing E40 lamp holder?
The ceramic E40 socket is rated for HPS and MH lamps up to 1000W. Ceramic construction ensures thermal resistance at sustained high operating temperatures that would degrade plastic-bodied alternatives over time. Only single-ended (SE) lamps with a standard E40 base are compatible — double-ended lamps require a different socket type entirely.
