- You cannot place a new order from your country (United States).
search
EC Standard 1,413 Growth Technology 300 ml
EC Standard 1.413 from Growth Technology is a conductivity reference solution fixed at 1.413 mS/cm, the internationally recognised calibration point for EC meters used in hydroponic and substrate cultivation. Electrode drift from mineral salt deposits on sensing pins produces progressive measurement bias that calibration corrects. Without regular recalibration, dosing decisions are based on inaccurate conductivity data, leading to either nutrient deficiency or salt accumulation at the root zone. This 300 ml bottle provides dozens of calibration sessions when dispensed into a clean separate container. Pair with EC Standard 2.76 for two-point calibration. Order from plantandflower.be with fast delivery across Belgium.
EC Standard 1.413 Growth Technology 300 ml – Conductivity Reference for Precision Nutrient Management
Every nutrient dosing decision in a hydroponic system depends on EC measurement accuracy. An uncalibrated conductivity meter introduces systematic error that propagates through every feed adjustment, reservoir top-up and drain-to-waste calculation. EC Standard 1.413 from Growth Technology provides the primary calibration reference at 1.413 mS/cm — the industry-standard value used by meter manufacturers for factory calibration. For comprehensive two-point calibration, combine with EC Standard 2.76 to define both offset and slope across the full working range.
Why 1.413 mS/cm is the industry reference point
The 1.413 mS/cm value derives from a standardised potassium chloride solution at 25°C, providing a traceable conductivity reference recognised by calibration laboratories worldwide. This specific value positions the calibration point at the centre of the typical horticultural working range — most nutrient solutions operate between 0.8 and 2.5 mS/cm depending on crop type and growth stage. Calibrating at a mid-range point minimises absolute measurement error across the span where growers make daily dosing decisions. Most commercial EC meters ship factory-calibrated to 1.413 mS/cm, making this solution the natural choice for periodic recalibration to restore original accuracy.
- Fixed 1.413 mS/cm value: internationally traceable conductivity reference stable under standard storage conditions.
- 300 ml bottle: provides dozens of calibration sessions with small-volume dispensing protocol.
- Universal compatibility: functions with all conductivity meters including pen-type, benchtop and continuous monitoring systems.
- Two-point calibration base: pair with EC 2.76 to correct both offset and slope simultaneously.
EC calibration impact on nutrient dosing accuracy
A measurement error of 0.2 mS/cm represents approximately 15 % deviation in dissolved salt concentration — a significant margin when managing precision feed programmes. In recirculating hydroponic systems, this error compounds with each reservoir adjustment. If the meter reads high, the grower under-feeds because the displayed concentration exceeds reality. If it reads low, progressive salt accumulation occurs as the grower adds nutrients to reach a target the solution has already exceeded. Both scenarios produce measurable crop impact within days. Regular calibration with a known reference standard eliminates this systematic bias. For growers managing multiple reservoirs or running feed-to-waste systems with tight EC targets, calibration accuracy directly translates to input cost efficiency and crop quality consistency.
Maintaining buffer integrity for repeatable results
Calibration accuracy depends on reference solution purity. Always dispense into a separate clean container — immersing the probe directly into the stock bottle introduces nutrient salt contamination that shifts the reference value permanently. Discard used solution immediately after each calibration. Store the sealed bottle at room temperature away from direct sunlight. The 1.413 mS/cm value is specified at 25°C — calibrate at room temperature for optimal accuracy. If your grow space runs significantly warmer, allow the solution to equilibrate before proceeding. Complement your calibration routine with regular EC probe maintenance to ensure the sensing pins remain free of mineral deposits that accelerate measurement drift between calibration intervals.
Order EC Standard 1.413 from plantandflower.be with fast shipping across Belgium. Reliable calibration data is the foundation of every successful feed programme.
How do I calibrate my EC meter with EC Standard 1.413?
Dispense a small volume into a clean container at room temperature. Rinse the probe, immerse it in the solution and enter calibration mode. Wait for the reading to stabilise at 1.413 mS/cm and confirm. Discard the used solution and never return it to the stock bottle.
What is the difference between EC 1.413 and EC 2.76 calibration solutions?
EC 1.413 is the primary mid-range reference point used by most meter manufacturers for factory calibration. EC 2.76 provides a higher reference for two-point calibration, enabling slope correction that improves accuracy at the upper end of the measurement range relevant to heavy-feeding bloom stage programmes.
How often should I calibrate my EC meter?
Calibrate every two weeks with daily use in nutrient solutions. Monthly calibration is sufficient for occasional use. Always recalibrate immediately after probe replacement, extended storage or when readings appear inconsistent with applied dosing.
Can I reuse EC calibration solution after use?
No. Contact with the probe transfers trace mineral salts into the solution, altering its conductivity value. Always use a fresh portion for each calibration and discard the used sample immediately to maintain reference integrity.
